Papiermaschinen
Hauptbild | Name | Hersteller | Typ | Größe | Kapazität |
---|---|---|---|---|---|
1 verfügbar |
Papiermaschine Fourdrinier 2500 mmGebrauchte Langsieb Papiermaschine Antriebe 60 Hz!
Trim width: 2500 mm Working speed: 150 - 350 m/min Design speed: 400 m/min Capacity: 120 t/d Basis weight: 90 - 215 gsm Drive: sectional drive BYDC and AC motor, belt pulley and reducer |
— | Fourdrinier | 2500 mm | 120 t/d |
1 verfügbar |
Langsieb-Papiermaschine 4200 mmGebrauchte corrugated medium Papermaschine: Type: fourdrinier Paper grade: corrugated medium Trim width: 4200 mm Speed: 600 m/min Grammage: 90 - 220 gsm Machine drive: sectional drive by DC motor and reducer Equipped with size press Location Asia, drive 60 HZ
|
— | Fourdrinier | 4200 mm | 550 t/d |
1 verfügbar |
Corrugating Board Paper (or Kraft paper) Mill+ Stock PreparationPaper: Kraft (or Corrugating Medium, Test Liner Paper) Basis weight: 31-100 GSM (or 220GSM) Maximum paper width: 6520 mm Production capacity: 400 ton/day Design speed: 1,110 m/min Nominal speed: 400~800mm/min Slight motion speed: 10~60mm/min (At sequence, operation monitoring settings possible) Leveling speed: 100~999.9m/min (At sequence, operation monitoring settings possible) Rate of change per second: 0.1~1m/min/sec (slow speed) 1~5m/min/sec (rapid speed) Change time settings: 10%/200 seconds (10% change time can be set) Coating in size press: max. 1g/m2 (double-side) Reel winding length: 74m Reel winding maximum diameter: 2600mm The number of machine sections: 12 sections The number of motors: 42units (Manufacturing year: 2004) Manufacturing year of electric equipment: 2004
|
Metso / Beloit / Mitsubishi | Twin wire (or four wires) | 6520 mm | 400 t/d |
1 verfügbar |
Paper machine 2550 mmmachine width: 2550mm Max. speed: 200 m/min BW range: 30-400grs/m² Supply voltage: 3 x 500 Volts Steam pressure: 4 bar Air pressure: 7 bar Water pressure: 2 bar Water consumption: 40 Lts/Kg Steam consumption: 3.0 Kg/kg PM only from headbox to pope-roll.
MACHINE DESCRIPTION Has produced a wide range of products: Production range is from 30 to 400 GSM running at 50 to 220 m/min. Paper with at reel is 2550 mm max. Capacity is up to 3500 Kg/h. Main characteristics is its formation uniformity CM and MD, gradual drying rate both wet and steam dried. GENERAL DESCRIPTION FORMING SECTION WITH DANDY ROLL It is a Fourdrinier type with removable table for wire change, cantilever couch roll, closed headbox for optimal flow rate at any speed and watermarking Dandy Roll. PRESSES Three 80 kg /cm2 presses, 2 lower felt and a 3rd upper felt, allowing good drying capacity and surface smoothing. Water content after presses is about 50% below 120 GSM. DRYING Consist in a main battery of 18 driers of 1250 mm diameter, in 3 drive sections with drying felts on both sides. Post drying after size press is done with 6 driers, 4 of 1000mm dia and 2 1250mm diameter in one drive section, with automatic paper moisture control. All driers tested at 4 Bar, heated with steam at 3.7 Bars max. All sections covered by a recovery heat hood that allows pocket ventilation at 90 degrees Celcius. SIZE PRESS Two rubber 350 mm diameter rolls working at 20 Kg/cm allows sizing with starch and latex. CALENDER STACK Küsters 400mm dia King roll, 2 intermediate 330mm dia rolls and un upper 400mm dia Queen roll that can be used as a one pass or three pass calender up to 80 Kg/cm. MACHINE DRIVE It is a line shaft with conical pulleys, pneumatic clutch and angular reducer for 11 sections. Motor drive is 300 Kw dc. SECURITY PAPER MACHINE
|
— | — | 2550mm | 3,5 t/h |
1 verfügbar |
Tissue paper manufacturing line 15 t/day with rewinderGebrauchte Tissuepapier Produktionslinie inklusive Stoffaufbereitung für Zellstoff sowie Umroller |
European | — | 2310 mm trim | 15 t/d |
1 verfügbar |
Used transformer board production line for saleUsed transformer board production line for sale: videos are available on demand. Scope of supply: Cellulose pulp preparation line: consists of two hydro pulpers for disintegration of 10 m³each, tanks, pumps, refiners 2 units with powers of 315 kw each, centrifugal sorters, etc. The sheet forming machine: consists of two stainless steel pick-up cylindrical sieves and a forming cylinder. Diameter in length: 2000 mm x 3200 mm. Sheets dimensions: 6300 mm x 3200 mm. Press: equipped with 8 pressing cylinders, arranged horizontally, with a diameter of 690 mm and working at 320 hydraulic bar
|
Swiss company Bell | — | — | 2500 t/year |
1 verfügbar |
Tissue paper production line 74 t/day with stock preparation and rewinderUsed tissue paper production line: Consisting of: Stock preparation for virgin pulp - Pulper - Refiners - Screening - Disc filter
Paper machine Headbox: Single layer, year 1990 ies Vacuum system
Rewinder with 4 unwind stands |
European | — | — | 74 t/day |